Posts

Showing posts from 2013

HT19 Split Collet Grips for turned dumbbell test specimens

Image
Tinius Olsen’s HT19 split collet chucks grip is designed for applications involving smaller turned dumbbell test specimens. The HT19 has a number of options to accommodate various size dumbbells with each split collet chuck set matched to a particular dimension of specimen. The HT19 grip a maximum capacity of 20kN and should not be used with a loadcell smaller than 50N capacity. Key parameters include diameter of turned gauge length, diameter of larger turned end section and the radius of the shoulder joining the end section and the gauge length. Tinius Olsen has higher capacity options for more traditional size specimens, so to learn what options are available for your application, please contact us.

PT190 - 90 degree Peel Test Attachment with moving Base Sledge

Image
PT190 is a 90 ° peel unit comprising of one HT50 ultra-light vice grip ( as standard) and a "horizontal Test bed". It is specifically designed for peel testing of the bond between copper and Printed Circuit Boards (PCB’s) as well as other laminate/layer bonded specimens, but can be used in a host of other peeling type applications. The PT190 is typically installed on a Tinius Olsen H5KS , or similar low capacity tensile tester and has a maximum capacity is 1.5kN (300lbf) with a minimum load cell of 50N. Prepared samples (150x50mm max.) are held on the test bed using a clamp with one end of the specimen inserted into the top clamp. The test bed incorporates a moving sled, mounted on precision bearings, which is directly attached to the moving crosshead of the test frame. As the crosshead moves up, the bad is pulled horizontally, so maintaining a peel angle of 90 ° throughout the duration of the test. To learn more about our grips and applications, please contact

HT58 grip for lightweight thread and yarn testing applications

Image
Tinius Olsen specifically developed the HT58 lightweight pneumatic grip for easy and repeatable thread/yarn testing. Designed for use with 10N load and calibrated for use between 10-1000 grams, the HT58 is used on the Tinius Olsen H5KS tensile tester. With a gripping pressure of 150N (15kgf), the HT58 eliminates the slip and its unique gripping face design prevents premature specimen breaks in the jaws. Its design allows quick and easy loading, for continuous commercial testing and accurate setting for repeatable gauge length choice. To learn more about our gripping technology, please contact us, here .

High Elongation U Series

Image
Tinius Olsen provides all kinds of customizations for our testing equipment and the most recent series to be modified is the U series. The U series machines are floor standing tension and compression materials testing machines, used to test the physical strength of a vast range of materials, and are available in maximum capacities from 100kN to 300kN.   Until now the maximum crosshead travel has been limited to 1,200mm, but with these new custom frames, this maximum has increased to 2,000mm. To achieve this 66% increase in test height, without increasing the machine height (of 2.85m) the machine’s controls and electronics are removed from the test frame and relocated into a separate housing, as seen in the artist rendition here.   All other machine performance specifications remain the same.

T Slotted Tables – why are they so useful?

Image
T-slotted tables are extremely useful when they’re used with materials testing machines because they provide an easy way to insert and clamp non-standard or large test samples. T-slotted tables themselves can come in all shapes and sizes – the one on the right here was designed to fit one of our 10,000lbf twin column bench-top testers (which itself is mounted on a frame) and is used by a conduit manufacturer to perform flexural tests on their products. The T-slots allow easy location of the flexural jig supports (which are anchored in the slots) so switching between different products is simple and quick. With all T slotted tables, the loading point MUST still be in the center of the specimen and in the same plane as the loadcell – any off-centered loading can give erroneous results and can also damage loadcells. This is true for all machines except Tinius Olsen’s Electomatic series of testing machines whose unique design, and key feature, allows and compen